How to apply the Pump Saver to your Pressure Washer?  

You might be asking yourself what pump saver is, especially if you don’t usually deal with this type of tool or with pressures washers in general. However, if you are more familiar than this piece of equipment can be both efficient but also save you lots of money in the long run when it comes to repairs and maintenance.

Pump Saver is a special applicant that is applied to the internal parts of a pressure washer pump to ensure that the useful life of the device is extended over long periods of time, especially when the pressure washer has to be placed in storage in areas where it will not be serviced for a while or not be used for a number of months.


What are the steps to applying pump saver? 

There are a series of steps that you should follow when applying pump saver to your pressure washer when you want to store your pressure washer or protect it against the effects of the weather. The steps required are quite simple and should provide you a number of benefits that you cannot afford to miss out on:

  1. First identify the pump inlet and outlet to your pressure washer.
  2. Flip the top off of the can of pump saver.
  3. Place your finger on the top of the pump saver bottle.
  4. Hook up the end of the pump saver tube nozzle to the pump inlet.
  5. Hold down the pump saver button to dispense the lubricant
  6. Hold down the pump saver button until you see lubricant leaving the pump outlet

If you have followed these steps then it should be clear that you have applied the pump saver properly, and that your pressure washer has been lubricated. The time it takes to apply the pump saver may vary depending on the pressure washer that you use. It should not take more than a few seconds.

Key Takeaway: If it is taking a considerable amount of time to see any results then that may be an indication of the condition of your pressure washer. If this is the case then it is advised that you take your pressure washer to the nearest professional or preferred professional location so that they can accurately and effectively investigate for you.


What pump savers are the most suitable for me? 

There are different brands and varieties of Pump Savers that can all be applied to the same scenario and types of machinery however some have small slight differences when compared to each other. Here is a selection of a few to give you an idea of the different types of Pump Savers and make it easier to select the best one for you:


Karcher 9.558-998.0 Gas and Electric Pressure Washer’s Pump Guard (16oz)

Karcher Pump Guard Anti-Freeze Protection for Electric & Gas Power Pressure Washers, 16oz
  • The Karcher Promise: Cleaner. Quicker. Best-in-class cleaning performance.
  • Prolongs the life of your electric or gasoline pressure washer
  • Guards against freezing down to -25 degrees Fahrenheit; highly recommended for winter storage!


Designed to prolong the life of your electric or gasoline pressure washer, this pump guard will help to protect from corrosion and premature wear on your pressure washer parts. Additionally it has freeze protection that protects down to -25 degrees Fahrenheit, as well as adding lubrication to the pressure washer valves and seals.

Reviewers find that this pump saver works effectively well as an unpressurized bottle of preservative when compared to others which are pressurized which ends up wasting more of the product than necessary. The lubrication and anti-freeze features are also considered to be a big plus to the product and its usefulness.

Some purchasers have had trouble properly applying this pump saver to their pressure washer and seem to require extra instructions as to how to effectively do this as it ends up wasting the material that is inside it. Additionally there has been a case of the pump saver evaporating quickly but this seems to be a controlled case.


Briggs & Stratton Pressure Washer Pump Saver – 4 Oz. 6039

Briggs & Stratton Pressure Washer Pump Saver - 4 Oz. 6039
  • Protects the pistons of your pressure washer and seals them from damage
  • Uses a unique anti-freeze and lubricant formula
  • For use before extended storage and prior to startup the following season to keep your pump running on full blast


This pressure washer pump saver also contains a unique anti-freeze and lubricant formula that will effectively help it to keep your pressure washer safe from the lower temperature colds that cause freezing as well as ensure that it can be actively revived after months in the shed and a lack of operational use.

A lot of purchasers have found this pump saver to be very effective at prolonging the useful life of their pressure washer due to the ability for it to be used as a lubricant alongside long time maintenance oil. It has been touted as helpful in keeping a good machine running for a much longer time as well as without maintenance hassle.

Once again there have been issues with the instructions of application not being entirely clear and some purchasers having difficulty in applying it properly, resulting in them wasting the product and providing negative feedback in their review. There is reason to believe that proper application will provide much more positive results.


AR North America Pressure Washer Pump Saver

Bestseller No. 1
Briggs & Stratton 6151 Pressure Washer Pump Saver Anti-Freeze and Lubricant Formula, 10.7-Ounce
  • Protects the pistons of your pressure washer and seals them from damage
  • Uses a unique anti-freeze and lubricant formula
  • For use before extended storage and prior to startup the following season to keep your pump running on full blast


A specific North American brand created by the company known as A.R. North America, this company deals with the creation, distribution and maintenance of pressure washer pumps and pump accessories. Aside from pump saver it has a variety of different components for pressure washers if you’re ever in the need for more parts.

This bottle of pump saver comes in a 16-ounce container and features an anti-freeze solution, perfect for storage in cold climates and cold areas where components of the pressure washer can succumb to freezing as a result of subzero temperatures, a particular problem in northern parts of the United States.

Some issues have previously been found with the purchasing online with the product arriving damaged and effectively unable to be used. This is an occurrence that can happen with all forms of online ordering however it should not be too greatly considered when making the purchase for a product.



With this information taken into consideration on how to apply the pump saver to your pressure washer as well as some tips on what types of pump saver you might want to purchase, hopefully you should have a better idea on how to maintain your pressure washer to ensure that it lives longer and can continue to get the job done.

How to select the right Sandblaster Attachment for your Pressure Washer?

Sandblasting is a method wherein an abrasive material, in this case a sand, is used to smoothen surfaces. A sandblaster attachment is placed onto the pressure washer so that it can propel fine bits of material at high-velocity. This is also very useful not only for cleaning and smoothing, but also for removing stubborn stuff like chipping paint and rust.

Even though sandblasters can work on its own, many recommend using sandblasters with water (attaching it to a pressure washer) because it becomes more effective. The water mixes with the sand and creates a powerful spray, allowing you use less sand and finish the job faster.

Buying a sandblaster attachment is also cheaper than buying an entire separate machine for this job. If you already own a pressure washer, all you have to do is purchase a sandblaster kit to attach to it. This is recommended especially if you intend to use your sandblaster occasionally.

There are many factors that may affect your purchase so make sure to read and know most of them before investing in a sandblaster. The prices vary; it can be very cheap to very expensive so you’ll want to get the best out of your buck.


What are the factors to consider when getting a sandblaster attachment for pressure washer?

Review each factor below to know what to look for in a sandblaster. These may vary according to your needs and wants as well as the type and power of the pressure washer you own.

Type – There are three main types of sandblasters. These are gravity-fed, siphon, and pressure. Here, we will only discuss about a single type, which is the pressure sandblaster, as the main course of action will be attaching the sandblaster onto your existing pressure washer.

There are sandblasting kits that come with sandblasting guns that are hooked onto the pressure washer. Pressure sandblasters are the easiest to use because all you have to do is hook it in and start blasting away. The only downside of this type is the fact that the sand can’t be reused so you’ll have to purchase new sand canisters every time you run out.

Size – You should look for a sandblaster that is compatible with your pressure washer. For instance, if you have a light duty pressure washer, ranging from 1,200 psi to 2,000 psi, get a sandblaster that can work with it without problems. The same should be applied for heavy-duty pressure washers of around 2,500 psi to 3,500 psi.

Also check for the capacity of the sandblaster to fire up sand. You can check how much weight it spews an hour as it is listed in the sandblaster’s specifications. The most common is about 200-300 kilogram an hour.

Kit – When buying a sandblaster attachment, make sure that everything that you’ll need is already included. The important parts that you should check out in the kit are the following:

  • Metal probe
  • Sand hose
  • Adjustable sand intake
  • Sand blast head
  • Different nozzle sizes
  • Safety goggles
  • Sand

The sand may or may not be included in the kit so you’ll have to buy it separately. You can get one such as the:


Black Diamond Blasting Abrasive

Although it is not “sand” per se, it works with all blasting equipment.


How do you attach the sandblaster to your pressure washer?

If this is the firs time you’re doing this, you can check the manual of both the pressure washer and sandblasting kit to study their different parts. When you’re familiar with them, follow the simple steps below:

  1. Connect the sandblast head to the sand hose. Pick the nozzle size you need and attach it to the sandblast head.
  2. Place the sandblaster induction probe in the sand supply container
  3. Connect the sandblast into the pressure washer
  4. Open the water supply line and connect the pressure washer to a power source
  5. Trigger the gun to activate the spray
  6. Test it on a scrap material first. The high pressure may damage the surface if you are too close

Don’t forget to always point the nozzle downward when you are spraying. This is to prevent the water from getting into the sand supply hose. As a safety precaution, also wear goggles and mask to protect the eyes and the face. Wear work gloves when spraying because the abrasive materials can definitely cut and scrape.


What are the best sandblaster attachments for your pressure washer?


Karcher Electric Pressure Washer Sandblasting Kit

Karcher Electric Pressure Washer Sandblasting Kit
  • An alternative to harsh chemicals^Includes safety goggles^Not suitable for use on delicate surfaces. Always test an inconspicuous area before using.^Genuine Karcher accessory.^Compatible with all Karcher consumer electric pressure washers


This sandblasting kit is compatible for Karcher electric pressure washers but can be tried with similar pressure washers. It comes with the nozzle and sand hose as well as free safety goggles.


Oregon 37-050 Pressure Washer Sandblasting Kit With 10-Inch Sand Hose 24-Inch Lance Extension 3650 Max PSI

3500 PSI Sandblasting Kit
  • General Pump
  • Tools & Hardware


This kit comes with a 10-inch sand hose and 24-inch lance. It only comes with one nozzle size, which is at 4.5 with 1.5mm orifice size. This sandblaster attachment is a bit on the expensive side. If you’re eyeing to purchase this, make sure that it’s really compatible. Otherwise, you can get cheaper ones below $100.


WSI International Sandblasting Kit – 3500 PSI, Model# FC 41069


This sandblasting kit can be used for pressure washers up to 3,500 psi. It includes an 8-ft hose, and nozzle size in 0.45. It has a steel material body and can move sand at 350kg per hour.

Key Takeaway: Make sure to check first if the sandblaster attachment you are eyeing is compatible for your pressure washer. You can take an example of the hose you are using with your washer and compare it with the size of the sandblaster, to make sure that it will fit.



Sandblaster attachments are great because it makes the pressure even more powerful, which is great not only for cleaning persistent dirt and grime, but also for removing paint and rust. These attachments are not that expensive and are more practical than buying a separate sandblasting equipment. If you already have a trusty pressure washer, just opt for this attachment.

How to replace or repair your Power Washer Pump?

One of the hardest fact to swallow is when your expensive power washer starts to encounter problems, such as leaking, which is very common even if you own the most expensive one sold in the market. The great thing about this is that it’s not the end of the world for your power washer as you can easily fix it.

The most common area affected when it comes to leaking is the power washer pump. You can either try to repair it, or replace it if you have found out that it’s completely broken. This is relatively easy to do; you don’t have to be a builder or a very knowledgeably handyman to pull this off.

As long as you know where the parts are located (or you’re familiar with it, at least), you have an idea who the whole thing works, you have the necessary tools, and you know how to follow instructions, then you can simply do the replacing or repairing of your power washer pump. No need to pay hundreds of bucks for a repair man or plumber.


What are the most common problems of power washer leaks?

The most common problem relating to power washer leaks is associated with the pump. There are two kinds worth knowing about:

  1. Pump Assembly – The pump assembly of the power washer is worth checking out after your first notice the leaks. The assembly may either be worn out or need to be rebuilt. The simplest way to deal with this problem is to replace the entire pump if it is a few years old and is always used.

If the pump is new or it is not used very often, the step to take is to rebuild the assembly and replace the seals. This way, you’ll be saving money, as the pump is still operational.

Buying a kit is the most cost-effective way to go as you’ll get everything you need in one set, such as the:


Briggs & Stratton 207365GS Pump Kit for Pressure Washers

Briggs & Stratton 207365GS Pump Kit for Pressure Washers
  • Pump kit for pressure washers
  • Genuine briggs and stratton part
  • Consult owners manual for proper part number identification


  1. Pump – You will notice if the pump is worn out, as there might be signs of breakage. When you open it and notice that it’s beyond repair, the only step to take is to replace the pump along with the entire assembly. Before doing so, it’s also worth checking trying to replace the pump assembly first as this step is cheaper.

After the new pump assembly has been installed and there’s still leaking, the problem lies to the pump. Purchasing a pump is not that expensive; you can buy it in most hardware stores. Most of them are also compatible to any type or brand of power washer you own.


Try Pressure Washer Pump Vertical Mount 7/8″ Shaft- FITS ANY MODEL

Vertical Pressure Washer Pump Replacement 2700 2.4gpm 308653045 308653052
  • Genuine OEM Replacement Pressure Washer Pump
  • Compatible with Many Brands of Homelite/Husky/Ryobi Pressure Washers


This one fits all brands of pressure or power washers of up to 2700 max psi. It comes oiled, sealed, and ready for installation.

Key Takeaway: Don’t be adamant when it comes to checking out what’s wrong with your power washer. If you see the first signs of leaking, do check out what’s wrong inside so you’ll be able to remedy the problem before it gets worse. Doing this will save you money in the long run, as the early damages may be minor. As for leaking, the first things to check out are the hoses, the pump assembly, and the pump itself.


What is the step-by-step procedure for replacing or repairing a power washer pump?

As mentioned, prepare the necessary tools for the repair or replacement. You may need something to remove the nuts and bolts that secure the pump in its place. Also make sure that the necessary materials are complete, such as the replacement pump as well as the pump assembly.

  1. Check if your pump is the axial cam or triplex plunger pump as these are the ones that can be replaced. If your pump is the wobble type, you better go look for a new power washer, as these can’t be replaced.
  2. Purchase a replacement pump that is compatible with the model of your power washer. Determine the type of pump (axial or triplex) and then the shaft diameter size. If you can, take the old pump with you when buying the new one so you can compare the sizes.
  3. Match your old pump’s pressure rating (PSI) and gallons per minute (GPM) with the new pump.
  4. Dismantle the power washer and find the pump to be replaced. Carefully remove it using the necessary tools. Bolts and nuts may secure it. Before you do this, don’t forget to disconnect the power washer from any power source for safety purposes.
  5. Before installing the new pump, ensure that you wrap thread tape around the thread to ensure a nice seal. You want the pump assembly to be in place as well.

You may want to get seals such as:


Briggs & Stratton 193807GS Pump Seal Set for Pressure Washers

Briggs & Stratton 193807GS Pump Seal Set for Pressure Washers
  • Pump seal set for pressure washers
  • Genuine briggs and stratton part
  • Set of 3 seals


  1. Place back all the connections and connect all tubes to the pressure washer.
  2. Turn on the power washer and do your usual cleaning chores to check if the replacement is successful. There should be no more leaks after this.

Key Takeaway: Finding the exact size and type of pump replacement may be one of the difficult tasks associated with the entire replacing process. Make sure to do your research so you’ll be able to get your hands on the perfect replacement. This way, you won’t encounter problems when you go through it.



Try your best to remedy a problem before it gets worse. A power washer is something that you want to take good care of, not only because it is expensive, but it’s also a tool that’s supposed to last you years of good use. A leaky pump is only a small problem and it can be easily fixed. Don’t scrap the entire power washer just because of this; do proper research as this can be easily repaired or replaced.

Electric Pressure Washer Reviews: How to buy the right one?

Electric is the way to go when it comes to pressure washers if you intend to own it for home use or for a bit of DIY projects. This is because electric pressure washers are very easy to use; they’re plug and play, meaning that after you have secured the electric connection for it, you’re ready to blast away.

This won’t give you hassles of having to buy fuel and reload your pressure water every time it runs out, such as in the case of gas pressure washers. It also doesn’t produce smoke that may be harmful, especially if you’re doing some cleaning indoors.

Electric pressure washers are considered the light-duty ones, compared to their gas brothers because your electric connection can only transfer a little bit, else you might have short circuit at home. They’re best used for chores around the house or for small contractor projects, as they are lighter, quieter, and easier to start.

If you’re looking for the best pressure washer, first consider reading through this ‘how to buy’ guide.


What are the factors to consider when buying the right electric pressure washer?

Although some models of electric pressure washers can be very affordable, you shouldn’t jump the gun because you’ll want to be able to purchase the one, which not only suits your needs, but also has the right qualities and features. To help you with deciding, we have listed some factors that you should consider:

  1. Ability to loosen dirt – This ability or power to loosen or blast away dirt can be measured in pounds per square inch (psi). If you’re aiming for a light duty electric pressure washer, look for machines that have 1,200 to 1,900 psi, as it can clean about 10 to 40 square feet in 10 minutes.

Medium duty pressure washers are around 1,950 to 2,600 psi, which is great for larger contractor jobs. Heavy-duty pressure washers, intended for commercial use, can be around 2,650 to 3,800 psi and it can clean 90 to 190 square feet in 10 minutes.

  1. Water consumption – Consider how much water the pressure washer intends to consume. You’ll know when you check the gallons of water per minute (GPM) that the pressure washer uses.
  2. Check out the accessories – For the price that you’ll pay, you want to get the important stuff associated with the pressure washer to make chores easier for you. Some of them are the rotating scrub brush, broom attachment, gutter attachment, etc. The pressure washer would still work without these, but it’s great to have because it makes the cleaning more thorough.
  3. Check the spray nozzle – It’s one of the most important parts of the pressure washer because it’s where the water comes out. You may want to get a telescoping wand to clean hard to reach areas. It also gives the user more comfort, as it’s easier to wield it.
  4. Heated water – You can get a pressure washer that expels heated water. However, this is more costly and consumes more electricity and water. The upside is that it can easily melt stubborn buildup of dirt and grime. For home use, this isn’t really advised to get.

Key Takeaway: Considering the above factors would make it easier for you to decide and look for the best electric pressure washer. It also gives you a clear idea of your needs, making you surer with the chosen pressure washer.


What are the best electric pressure washers?

We have listed three electric pressure washers worth checking out, accompanied by short descriptions:


AR Blue Clean AR383 1,900 PSI 1.5 GPM 14 Amp Electric Pressure Washer with Hose Reel

AR Blue Clean AR383 1,900 PSI Electric Pressure Washer, Nozzles, Spray Gun, Wand, Detergent Bottle & Hose
  • OUTDOOR CLEANING POWER: Make quick cleaning jobs of decks, patios, siding, driveways, outdoor furniture, cars, trucks, RVs, ATVs and more.
  • ATTACHMENTS INCLUDED: Professional-style pressure washer gun, 2 different pressure washer wands, 20 foot high pressure hose, 14 oz. detergent bottle and 2 high pressure quick change wands with pressure washer turbo and variable nozzles. Hose diameter: 0.25 inch
  • ENVIRONMENTALLY FRIENDLY: Conserves water by using 80% less water with 40% more power than a standard garden hose. Quieter than gas engine models.


This pressure washer is powerful enough to tackle persistent dirt due to its 1900 psi and 1.5 GPM. It has a 20-ft. hose so you can reach more areas and 30-ft. power cord so the use of extension cords is negated.

This electric pressure washer only uses cold water and is constructed from durable copper, aluminum, and plastic. The package comes with an accessory kit composed of gun, adjustable jet nozzle, high-pressure hose and lance with foam dispenser. The pressure washer can be taken anywhere with ease because it is mounted on a two-wheel trolley.


Sun Joe SPX3000 2030 PSI 1.76 GPM Electric Pressure Washer, 14.5-Amp

Sun Joe SPX3000 Pressure Joe 2030 PSI 1.76 GPM 14.5-Amp Electric Pressure Washer
  • 5 Quick-Connect spray tips (0º, 15º, 25º, 40º and soap) tackle light, medium and heavy duty cleaning tasks
  • Powerful 14.5-amp/1800-Watt motor generates up to 2030 PSI/1.76 GPM for maximum cleaning power and water inlet temperature (max) is 104 degrees Farenheit
  • TSS (Total Stop System) - automatically shuts off the pump when trigger is not engaged to save energy and prolong pump life.Working Pressure:1450 PSI.20 foot high pressure hose


This pressure washer comes with a detergent selection dial so you can effectively use soap while cleaning. It has a powerful motor, 14.5 amp and 1800 watt, that effectively support its equally powerful pressure at 2030 psi.

Stubborn gunk and grim don’t stand a chance with this pressure washer because of its above-average power. It has a dual detergent tank system that lets you carry two types of detergent simultaneously and lets you select which one to use using the dial. The 34-inch spray wand and rear wheels lets you maneuver easily and clean hard to reach areas.


Campbell Hausfeld PW1825 1800 PSI Electric Pressure Washer

Campbell Hausfeld Power, 1500 PSI, 1.75 Max with Nozzles GPM PW150100 Electric Pressure Washer
  • 20-Ft high-pressure hose, multiple nozzles and onboard storage for easy access to accessories and hose. 1, 500 max psi, 1.75 max GPM
  • Easy-connect tight connection points allow for easy changing of accessories and seamless switching between cleaning tasks
  • Built-in wheels, lightweight design and Small product footprint make the unit portable and easy to store


This electric pressure washer is very affordable, considering you’re in for some strong pressure at 1800 psi and 1.5 GPM output. It has a 20-ft. high-pressure hose that comes with a spray gun, fan lance, and turbo lance.

The 120-volt, 14 amp motor is lightweight and reliable. It is also very quiet, odorless, and don’t have any emissions, making it safe for indoor use. You can also add detergent onto the onboard detergent tank that holds up to one liter of any high pressure water solution for an even deeper cleaning.

Key Takeaway: The electric pressure washers listed here are very affordable and are made of quality materials that aim to last you years of use. Make sure to read through the specifications of each to find out if it really suits your needs.



Electric pressure washers are great tools for cleaning because they do the job faster compared to manual scrubbing. It also lessens the effort on your part, as all you have to do is direct the hose onto the area to be cleaned and the high-pressure water will do the job for you. No dirt, grit, and grim can’t be removed by pressure washers.

How to select the best Pressure Washer?

Pressure washer is a tool that connects to a water source, most commonly your garden hose, to give more cleaning power than what you can get normally from the hose alone. It lets you do your cleaning job faster because the spritz of water is much stronger. It is effective for removing dirt very quickly and it eliminates the need for scrubbing.

The high-powered stream of water caused by the pressure washer is effective for cleaning car, empty swimming pool, garage and driveway, decks, and many more. Using it blasts away the build up of hardened mold, mildew, dirt, and grime and restores the surface of the material to like new condition.

With a pressure washer, you don’t have to spend hours just brushing tirelessly because the pressure washer is able to do that and more in half the time or less. If you’re looking into getting a new pressure washer or you’re replacing an old one, it’s noteworthy to check some factors to consider before purchasing the best pressure washer.


What are the factors to consider when choosing the best pressure washer?

Pressure washers should take a considerable amount of time before buying because this tool is a bit expensive. You’ll also want to get something that is necessary for your needs because some kinds are too strong for your intended usage. Below we have listed some factors to consider when choosing the right pressure washer:

Fuel – There are two main choices for this: Gas and Electric. If you aren’t sure on which one is the best for you, take time to read more about the differences of each.

  • Electric Pressure Washer: To give you an idea, electric pressure washers are light-duty ones that are perfect for cleaning smaller areas that aren’t very dirty. These are quieter and easier to take from place to place.

Electric pressure washers are recommended for home use where you have to do cleaning chores such as washing the car, pavement, and rooms. Make sure to always have a socket near the area to be cleaned because it’s not recommended to plug it onto an extension cord.

The downside for this type of washer is that it may not be strong enough for intensive cleaning or for jobs that take hours but it is perfect for lighter house chores. Try:


Sun Joe SPX3000 2030 PSI 1.76 GPM Electric Pressure Washer, 14.5-Amp

Sun Joe SPX3000 Pressure Joe 2030 PSI 1.76 GPM 14.5-Amp Electric Pressure Washer
  • 5 Quick-Connect spray tips (0º, 15º, 25º, 40º and soap) tackle light, medium and heavy duty cleaning tasks
  • Powerful 14.5-amp/1800-Watt motor generates up to 2030 PSI/1.76 GPM for maximum cleaning power and water inlet temperature (max) is 104 degrees Farenheit
  • TSS (Total Stop System) - automatically shuts off the pump when trigger is not engaged to save energy and prolong pump life.Working Pressure:1450 PSI.20 foot high pressure hose


  • Gas Pressure Washer: These are great for heavy-duty cleaning because they can endure hours of non-stop washing. The types of gas pressure washers range from medium to extra heavy duty. If you intend to do a lot of cleaning at home, you can go for the medium one as the heavy duty may be industrial grade and too strong for your needs.

Even if you don’t need the great power, gas pressure washers are good if you are very mobile and want to reach more areas, especially outdoors as you won’t need to worry about lugging a cord behind you. It gives you more mobility, although they are slightly heavier because of the weight of the motor.

Most gas pressure washers don’t start with just the press or a button like electric ones; most light duty ones are a manual pull-start but some heavy duty ones come with an electric starter. Check out:


Generac 6596 2,800 PSI 2.5 GPM 196cc OHV Gas Powered Residential Pressure Washer

Generac 7019 OneWash 3,100 PSI, 2.4 GPM, Gas Powered Pressure Washer and PowerDial Gun
  • Ergonomic spray gun with integrated Power Dial allows you to easily adjust the pressure needed between four different tasks - car, wood, concrete and soap - at your fingertips
  • Powerful horizontal axial cam pump delivers 3100 PSI for tough cleaning
  • Convenient on-board 1/2 gallon detergent tank for hassle free cleaning


Power – After you have chosen the power source of your pressure washer, you need to consider next the power or capacity of your pressure washer. There are keywords to guide you, ranging from light duty to extra heavy duty with the lightest having around 1500 psi and the strongest around 3300 psi and up

When buying pressure washers, you should check the psi, which is the measurement of the ability of your pressure washer to loosen dirt in a certain area. psi stands for pounds per square inch. Lighter psi washers can clean about 10 to 40 square feet in 10 minutes while big psi washers can clean 90 to 190 square feet in the same amount of time.

If you don’t intend to clean a very large and very dirty area very often, don’t consider buying a heavy-duty pressure washer because you certainly don’t need it. Consider your cleaning needs and then assess it along with the pressure washer in mind.

For home use, the:


AR Blue Clean AR383 1,900 PSI 1.5 GPM 14 Amp Electric Pressure Washer with Hose Reel

AR Blue Clean AR383 1,900 PSI Electric Pressure Washer, Nozzles, Spray Gun, Wand, Detergent Bottle & Hose
  • OUTDOOR CLEANING POWER: Make quick cleaning jobs of decks, patios, siding, driveways, outdoor furniture, cars, trucks, RVs, ATVs and more.
  • ATTACHMENTS INCLUDED: Professional-style pressure washer gun, 2 different pressure washer wands, 20 foot high pressure hose, 14 oz. detergent bottle and 2 high pressure quick change wands with pressure washer turbo and variable nozzles. Hose diameter: 0.25 inch
  • ENVIRONMENTALLY FRIENDLY: Conserves water by using 80% less water with 40% more power than a standard garden hose. Quieter than gas engine models.


Is just right. It has a good enough number of psi for cleaning around the house.

Key Takeaway: Your main guide to buying the best pressure washer to accommodate your needs rests in the psi, or the power of the washer. If you intend to do cleaning around the house as part of your routine chores, choose a light to medium washer.


Why do you need to consider the power of your pressure washer?

Just because a pressure washer with very high psi is cheaper than the one that you need doesn’t mean that you have to buy it. Remember, the higher the psi and capacity of your pressure washer, the more costly it is to run it. Although it can clean a considerable amount of area, it can consume a lot of water and energy that can be unnecessary.s

Powerful pressure washers add weight and cost when it comes to fuel/electricity and water. If you intend to use it to clean a car or a small portion of your patio or deck, you’re using too much power for something so small. You can get the job done with a smaller pressure washer without having to spend a fortune on fuel and having to carry a very heavy one.

Key Takeaway: Consider if your needs fall to consumer or professional. This way, you can decide faster on the right power of pressure washer to use.



Pressure washers are a great addition to every home because it makes cleaning more thorough and much faster. You don’t have to scrub for hours because the pressure washer is strong enough to take out dirt and grime in just one direct hit.